0>>>CONCAT(CHAR(60),'/head',CHAR(62))
Online Consultation
TESTING ARTICLE

zirconium carbon brick testing

2026-11-16 20:17:30In About Us

Testing Information

Zirconium carbon brick testing is a third-party laboratory service that ZHONGXI Testing provides for zirconium carbon (ZrC-containing) refractory bricks, the carbon-bonded refractory products used in the linings of blast furnace tuyere zones, continuous casting tundish impact pads, slide gate plates, launder linings, and other severe-service areas of steelmaking and metallurgical vessels. Zirconium carbon bricks combine a carbon matrix with zirconia- or zirconium-bearing aggregates and additives, giving them the thermal shock resistance, slag corrosion resistance, and erosion resistance required in contact with molten steel, ferroalloys, and acidic or basic slags. They are also applied in glass tank furnace regenerators, non-ferrous melting furnace linings, and waste incineration furnaces where combined alkali attack and thermal cycling demand a carbon-bonded zirconia-containing refractory.

The purpose of testing these bricks is to verify whether the delivered products conform to the chemical composition, physical property, and mineralogical requirements specified by the purchaser or the applicable product standard, and to diagnose failure or abnormal wear in used bricks removed from service. Because the service life of a lining depends on a coordinated set of properties, testing covers the full property chain: raw chemistry (ZrO2 content, total carbon, impurity oxides), phase and microstructure (zirconia phase distribution, graphite orientation, porosity morphology), and performance metrics such as bulk density, apparent porosity, cold crushing strength, hot modulus of rupture, thermal shock resistance, slag corrosion depth, and oxidation behavior under CO2 or air at elevated temperature. The laboratory uses X-ray fluorescence spectrometry and combustion infrared carbon/sulfur analysis for chemistry, X-ray diffraction with Rietveld quantification for phase analysis, mercury intrusion and gas adsorption porosimetry for pore structure, and high-temperature mechanical testing frames equipped with carbon-resistance or induction furnaces for hot strength and thermal shock evaluation.

A typical testing engagement follows a defined sequence: sample registration and visual inspection of as-received bricks; cutting of cylindrical or cubic specimens with diamond tools while avoiding dried-in cracks; drying to constant mass at 110 °C before density and porosity determination; chemical analysis on fused beads and combusted powders; phase analysis on crushed subsamples; mechanical testing at ambient temperature and, where required, at 1100–1400 °C in protective atmosphere; thermal shock cycling between 950–1100 °C and water or forced-air quench media with residual strength measurement; and cup-type or rotating-slag static corrosion tests against reference slags of specified basicity. Core reported parameters normally include ZrO2 content (commonly 60–85 wt% on the zirconia-bearing grade), total carbon content (typically 8–20 wt% depending on resin-bonded or carbon-bonded design), apparent porosity (commonly 12–20%), bulk density (commonly 3.0–3.8 g/cm3), cold crushing strength, hot modulus of rupture at 1400 °C, and oxidation mass loss after controlled exposure, each compared against the specification band agreed in the purchase contract.

zirconium carbon brick testing Testing Items

  •  
  • High-frequency induction combustion infrared carbon and sulfur analyzer for total carbon and sulfur determination.
  • X-ray diffractometer with high-speed detector for phase identification and Rietveld quantitative phase analysis.
  • Scanning electron microscope with energy-dispersive X-ray spectroscopy for microstructure imaging and elemental mapping.
  • Mercury intrusion porosimeter covering the 0.003–360 micrometer pore diameter range for pore structure characterization.
  • Automatic bulk density and apparent porosity analyzer using the boiling-water and vacuum-saturation immersion method.
  • Computer-controlled electro-hydraulic compression testing machine with 600 kN capacity for cold crushing strength.
  • Three-point flexural testing fixture with digital load cell for modulus of rupture at ambient temperature.
  • High-temperature modulus of rupture furnace with carbon-resistance heating and protective atmosphere control to 1500 °C.
  • Automatic thermal expansion dilatometer for coefficient of thermal expansion measurement to 1400 °C.
  • Laser flash thermal conductivity analyzer for thermal diffusivity and derived conductivity at service temperatures.
  • Horizontal tube furnaces with controlled gas mixing (air, CO2, Ar) for oxidation and decarburization tests.
  • Thermal shock test rig with programmed quench cycles between furnace and water or forced-air cooling stations.
  • High-temperature slag corrosion furnace with rotating specimen holder for dynamic dip-and-rotate erosion testing.
  • Muffle furnaces and drying ovens with 110–1200 °C range for reheating, curing, and permanent linear change tests.
  • Laser particle size analyzer for verifying aggregate and powder granulometry of raw materials and crushed brick fractions.
  • Helium gas pycnometer for true density determination of powdered samples.
  • Precision analytical balances with 0.1 mg readability for gravimetric oxidation and absorption measurements.
  • Diamond sectioning saw and core drilling machine for damage-free specimen preparation from full bricks.
  • Digital calipers, dial comparators, and dimensional gauges for dimensional and flatness/tolerance checking.

Summary

Zirconium carbon brick testing covers the chemical, physical, mechanical, thermal, and service-simulation properties of ZrO2-C refractory bricks, including ZrO2 and carbon content, porosity and density, cold and hot strength, thermal shock resistance, oxidation behavior, and slag corrosion depth. ZHONGXI Testing accepts whole bricks, cut specimens, powders, monolithic mixes, and service-exposed samples, with test programs assembled from individual items or a full standard battery according to the applicable refractory test methods. Testing turnaround for routine property packages is typically arranged within five to ten working days, while slag corrosion, hot strength, and post-mortem programs run longer due to furnace scheduling and specimen preparation.

Related Testing

Send us your samples, keep the certainty.

Engineers online 8:00-20:00 (GMT+8), AI support 24/7; reports generally in 7-15 working days.

Address: Room 118, 1st Floor, Building 1, No. 8 Hangfeng Road, Fengtai District, Beijing, China · Google Maps