Testing Information
Elastomer testing is the systematic evaluation of rubber-like polymeric materials that exhibit high elastic recovery, and ZHONGXI Testing provides this service for manufacturers and processors working with natural rubber, synthetic rubbers, thermoplastic elastomers, and elastomeric compounds used across the automotive, construction, medical, electronics, footwear, seal, and hose industries. Elastomers are the functional core of products such as tires, O-rings, gaskets, vibration isolators, medical tubing, cable jackets, conveyor belts, and flexible couplings, and their performance in service depends on a complex balance of formulation, cure state, filler dispersion, and resistance to heat, oils, ozone, and repeated deformation.
The purpose of elastomer testing is to quantify how a material behaves under mechanical load, environmental exposure, and long-term aging, so that formulators can validate compound changes, quality engineers can verify incoming raw materials, and design engineers can select materials with data rather than assumption. Testing techniques span static mechanical methods such as tensile, tear, and hardness measurement; dynamic methods such as DMA and rebound resilience; rheological methods such as moving-die rheometry and Mooney viscosity; chemical and structural methods such as FTIR identification, TGA filler and oil content analysis, DSC glass transition determination, and density measurement; and durability methods including compression set, heat aging, fluid resistance, ozone cracking, and fatigue life evaluation.
A typical testing workflow begins with sample registration and a review of the material specification or part drawing, followed by specimen preparation — die-cut dumbbells from cured sheets, sectioned rings or buttons from finished parts, or compression-molded plaques when only compound stock is supplied. Cured-state checks such as hardness, density, and rheometer re-cure may be run to confirm cure adequacy before mechanical testing. Core mechanical parameters are then measured: tensile strength, elongation at break, and 300% modulus, tear strength, and hardness (Shore A or IRHD). Depending on the specification, environmental conditioning follows — heat aging at elevated temperature, oil or fuel immersion, ozone exposure, low-temperature brittleness or TR-10 testing — after which the mechanical tests are repeated to calculate retention of properties. Data are compiled into a testing report listing each parameter, the method applied, the conditioning conditions, and the measured results alongside the specification limits when supplied by the customer.
elastomer testing Application Scenarios
In the automotive sector, elastomer testing supports the development and validation of sealing systems, hose compounds, bushings, and vibration isolators. A compound change for an engine mount, for example, requires verification of tensile and tear properties, compression set at the operating temperature, heat aging retention after 70 or 168 hours at 100–150 °C, oil swelling to confirm compatibility with engine lubricants, and low-temperature brittleness to ensure cold-start sealing. Brake and fuel line compounds add volume swell testing against reference fuels and permeability-relevant composition checks, while thermoplastic elastomer duct and weatherstrip parts require hardness, tensile, and heat-aging data on injection-molded plaques.
In the medical and pharmaceutical field, silicone and latex products demand strict material verification. Tubing, closures, seals, and dipped goods are tested for polymer identity by FTIR, extractables and volatile content, compression set for stopper resealing behavior, tensile and elongation for film integrity, and biocompatibility-relevant baseline physical data that feeds into downstream biological evaluation programs. Thermoplastic polyamide and TPU compounds used in medical garments and device components are additionally characterized for their thermal transitions and sterilization stability.
In the construction and infrastructure market, EPDM membranes, bridge bearing pads, expansion joint seals, and roofing membranes are tested for long-term durability. Ozone and weathering resistance, compression set under sustained structural load, tear propagation resistance at lap seams, hardness change after heat aging, and water absorption are the decisive parameters that determine service life in outdoor exposure. Roofing membrane compound verification also includes tensile behavior in both machine and transverse directions to detect calendering-induced anisotropy.
In consumer, industrial, and electronics applications, elastomer testing covers footwear midsole and outsole compounds, TPU cable jackets and connectors, keyboard and sealing components in electronic devices, polyurethane wheels and wear parts, and sponge and foam sealing profiles. Here, rebound resilience and compression fatigue govern cushioning performance, abrasion resistance governs sole and wheel life, hardness defines tactile and fit characteristics, and plasticizer or oil extraction testing verifies that compounds will not stain or contaminate contact surfaces. Wire and cable compounds add aging, deformation under load, and insulation-relevant physical testing to confirm jacket integrity over the rated temperature range.
elastomer testing Testing Items
- Tensile strength — the maximum stress a cured compound sustains before rupture, a fundamental indicator of cure state and filler reinforcement
- Elongation at break — measures the deformability of the compound and reflects crosslink density and polymer flexibility
- modulus — stress at strain, used to assess crosslink density and reinforcement level independent of failure point
- 300% modulus — stress at 300% strain, a key comparison point between compounds of similar hardness
- Tear strength — resistance to propagation of a cut or nick, critical for diaphragms, bellows, and molded parts with stress concentrators
- Shore A hardness — surface indentation hardness that defines compound classification and part fit
- Shore D hardness — used for harder thermoplastic elastomer and highly filled compounds above roughly 90 Shore A
- IRHD hardness — international rubber hardness degrees, required in many European specifications and preferred for finished parts
- Compression set — permanent deformation after sustained compression at elevated temperature, the decisive parameter for sealing compounds
- Heat aging retention — percentage retention of tensile, elongation, and hardness after air oven aging, quantifying thermal stability
- Fluid immersion swelling — mass and volume change after oil, fuel, or chemical immersion, indicating media compatibility
- Fluid immersion property change — change in hardness and tensile properties after fluid exposure, revealing plasticizer extraction or polymer attack
- Ozone resistance — resistance to surface cracking under static or dynamic strain in ozone-enriched atmosphere, essential for outdoor seals and tire sidewalls
- Low-temperature brittleness — the temperature at which the compound fractures under impact, defining the service temperature floor
- TR-10 / TR-70 retraction — low-temperature retraction temperatures that characterize crystallization and flexibility recovery
- Rebound resilience — the energy return of a compound, relevant for vibration isolation, sports surfaces, and midsole foams
- Mooney viscosity — processing viscosity of the uncured compound, governing mixing, extrusion, and molding behavior
- Mooney scorch time — time to premature vulcanization at processing temperature, determining safe processing window
- Moving-die rheometer cure curve — full vulcanization profile including ML, MH, tS2, tC50, tC90, and torque difference for cure validation
- Density — specific gravity measurement that verifies compounding consistency and detects voids or contamination
- Carbon black content — thermogravimetric quantification of filler loading, which dominates modulus and abrasion behavior
- Ash content — inorganic residue after combustion, revealing total inorganic filler and identifying formulation deviations
- Solvent extract — amount of oils, resins, and soluble additives extractable from the cured compound
- Glass transition temperature — DSC determination of Tg, which defines the low-temperature flexibility limit of the polymer phase
- Abrasion resistance — volume loss under standardized abrasion, critical for treads, soles, and wear liners
- Adhesion strength — bond strength of rubber-to-fabric, rubber-to-wire, or rubber-to-metal assemblies
- Compression fatigue and heat build-up — dynamic compression testing that measures temperature rise and permanent set under cyclic load, relevant to tire and damping compounds
- FTIR material identification — spectroscopic confirmation of the base polymer type for incoming material verification
FAQ
Which items are typically included in elastomer testing?
A standard elastomer testing program covers mechanical properties (tensile strength, elongation at break, and 300% modulus, tear strength, hardness on Shore A/D or IRHD scales), rheological and cure behavior (Mooney viscosity, Mooney scorch, moving-die rheometer cure curves with tS2, tC50, tC90, ML, MH and torque difference), aging and environmental resistance (heat aging with property retention, compression set at 70–150 °C, oil and fuel swelling, ozone cracking under static and dynamic strain, low-temperature brittleness, TR-10 retraction), and compositional or physical properties (density, ash content, carbon black content by thermogravimetric analysis, solvent extract, FTIR material identification, DSC glass transition, and rebound resilience). Customers may select the full suite or a subset matched to their specification; for example, a seal compound program usually emphasizes compression set, fluid resistance, and low-temperature behavior, while a tire tread compound program emphasizes tensile, tear, abrasion, and dynamic properties.
What sample types are accepted for elastomer testing?
Accepted sample forms include cured rubber sheets approximately 2 mm thick for die-cut tensile specimens, compression-molded plaques prepared from uncured compound stock, finished parts such as O-rings, grommets, seals, bushings, hose sections, and rollers, die-cut or water-jet-cut components from large articles, latex films and dipped goods, thermoplastic elastomer pellets that are injection or compression molded into test plaques, and finished foam or sponge products. For rheometer testing, approximately 20–30 grams of uncured compound is sufficient; for Mooney viscosity, roughly 30 grams of compound is used. When a customer sends a finished part that is too small or too irregular for standard dumbbell specimens, miniature specimens or alternative methods such as hardness, density, and micro-FTIR can be applied. Rubber-to-metal bonded parts can be accepted whole for bond strength evaluation.
Which standards does elastomer testing follow?
Testing is performed according to internationally recognized method standards selected to match the material and part type. Commonly applied families include ISO 37 and ASTM D412 for tensile properties, ISO 48 and ASTM D2240 for hardness, ISO 34 and ASTM D624 for tear strength, ISO 815 and ASTM D395 for compression set, ISO 188 and ASTM D573 for heat aging, ISO 1817 and ASTM D471 for fluid resistance, ISO 1431 for ozone resistance, ISO 132 and ASTM D1054 for rebound resilience, ISO 37, ISO 7619 for hardness of finished parts, ISO 289 and ASTM D1646 for Mooney viscosity, and ISO 6502 / ASTM D5289 for moving-die rheometry. Thermogravimetric and compositional work follows ISO 9924 and ASTM D6370, density follows ISO 2781 and ASTM D297, and low-temperature behavior follows ISO 812, ISO 2921, and ASTM D2137. Customer or OEM material specifications are applied directly when supplied with the sample.
Which testing methods are used for identification and composition analysis of elastomers?
Material identification typically begins with FTIR spectroscopy, where the polymer is solvent-extracted and the resulting film or pyrolysate spectrum is matched against reference libraries to distinguish NR, SBR, NBR, EPDM, CR, silicone, FKM, and thermoplastic grades. Pyrolysis-GC/MS is used for complex blends and to detect co-cured rubber mixtures that FTIR cannot fully resolve. Differential scanning calorimetry determines the glass transition temperature, which distinguishes polymer classes and reveals blend morphology. Thermogravimetric analysis quantifies oil content, polymer content, carbon black loading, and inorganic ash by monitoring mass loss under nitrogen and air atmospheres in a controlled temperature program. Elemental techniques such as EDX or ICP-OES identify inorganic fillers and halogen content, and solvent extraction with subsequent gravimetric or chromatographic analysis measures process oils and additives. These methods are combined to construct a full formulation picture when a customer needs to verify an incoming compound or reverse-check a supplier change.
Testing Scope
- Natural rubber (NR) compounds — smoked sheet and latex-grade formulations for tires, bushings, vibration mounts, and elastic goods
- Styrene-butadiene rubber (SBR) compounds — emulsion and solution SBR for tire treads, conveyor belts, and molded mechanical goods
- Butadiene rubber (BR) compounds — high cis-BR blends for abrasion-critical tread and sole applications
- Nitrile butadiene rubber (NBR) compounds — medium and high acrylonitrile grades for oil seals, fuel hose liners, and diaphragms
- Hydrogenated nitrile rubber (HNBR) compounds — peroxide-cured HNBR for timing belts, high-temperature seals, and oilfield packers
- Ethylene propylene diene monomer (EPDM) compounds — for window seals, radiator hoses, roofing membranes, and wire insulation
- Chloroprene rubber (CR, neoprene) compounds — for weather-resistant seals, hose covers, wetsuit materials, and bearing pads
- Butyl rubber (IIR) and halobutyl (BIIR/CIIR) compounds — for inner tubes, tire innerliners, pharmaceutical closures, and damping parts
- Silicone rubber compounds — high-temperature-vulcanizing (HTV) and peroxide or platinum-cured grades for medical tubing, gaskets, and insulators
- Liquid silicone rubber (LSR) — injection-molded medical parts, baby care products, and seals requiring low compression set
- Fluoroelastomer (FKM, Viton-type) compounds — for chemical-resistant seals, O-rings, and fuel components
- Perfluoroelastomer (FFKM) parts — for semiconductor and aggressive chemical service where extreme media resistance is required
- Polyurethane elastomers (PU/AU/EU) — cast and thermoplastic urethanes for wheels, scraper blades, couplings, and wear liners
- Thermoplastic polyurethane (TPU) — Shore hardness grades from about 70A to 75D for tubing, film, cable sheathing, and footwear
- Styrenic block copolymers (SBS/SEBS/SIS) — TPS compounds for grips, sealants, elastic films, and modified bitumen membranes
- Thermoplastic olefin elastomers (TPO/TPV) — for automotive glazing seals, air ducts, and weatherstrip profiles
- Thermoplastic copolyester elastomers (TPEE/COPE) — for bellows, CVJ boots, and flexible couplings with high fatigue resistance
- Thermoplastic polyamide elastomers (TPA/PEBA) — low-density flexible grades for sports midsoles and high-resilience components
- Chlorosulfonated polyethylene (CSM) compounds — for chemically resistant hose covers, tank linings, and coated fabrics
- Epichlorohydrin rubber (CO/ECO) compounds — for fuel and emission hoses with low permeability
- Acrylic rubber (ACM/AEM) compounds — for high-temperature automotive seals, gaskets, and transmission components
- Ethylene-vinyl acetate (EVA/EVM) elastomers — for midsole foams, solar encapsulation film, and hose cover compounds
- Natural latex products — gloves, condoms, elastic threads, and dipped goods with protein and extractables concerns
- Reclaimed and devulcanized rubber — recycled content materials verified by rheology, solvent extract, and mechanical testing
- Elastomeric finished parts — O-rings, gaskets, oil seals, bushings, bellows, diaphragms, vibration isolators, and rubber-to-metal bonded assemblies
- Elastomer sheets, membranes, and calendered fabrics — roofing membrane, pond liner, and coated textile materials
- Elastomer foams — closed-cell sponge profiles, open-cell foam pads, and midsole foam formulations tested for density and compression behavior
Summary
Elastomer testing covers the mechanical, rheological, environmental, and compositional characterization of natural and synthetic rubbers, thermoplastic elastomers, and finished elastomeric parts, from tensile, tear, and hardness measurement through cure rheometry, aging, fluid resistance, ozone resistance, low-temperature behavior, and formulation analysis. ZHONGXI Testing accepts samples ranging from uncured compound stock and cured sheets to finished O-rings, seals, hoses, membranes, and foam products. Testing scope is defined by the customer specification or by internationally recognized method standards, and data are delivered in a structured testing report for each requested parameter.